161+ Flat Roof House Insurance Uk

161+ Flat Roof House Insurance Uk

  18.12    insanu

---

www.apartmentguide.com

Opening: Build Your Own Simple Wooden Birdhouse Want to attract some feathered friends to your backyard? Building a simple wooden birdhouse is a fun and rewarding project that's perfect for beginners. This step-by-step guide will walk you through the process, from gathering materials to hanging your finished birdhouse. Let's get started!

Step 1: Gather Your Materials Before you begin, you'll need to collect the necessary materials. Here's a list of what you'll need:

Untreated wood (pine, cedar, or redwood are good choices avoid pressure-treated wood) A single 1x6 board, approximately 6 feet long, should be sufficient.

Saw (hand saw or power saw)

Measuring tape

Pencil

Drill with various drill bits

Screws or nails

Sandpaper

Wood glue (optional)

Exterior paint or stain (optional, but recommended for weather protection)

Step 2: Cut the Wood Pieces Using the following dimensions, cut the wood pieces for your birdhouse. These dimensions are a guideline and can be adjusted to your preference, just maintain proportions:

Front: 6 inches wide x 8 inches tall

Back: 6 inches wide x 10 inches tall (the extra height will create an overhang for the roof)

Sides (2 pieces): 6 inches wide x 7 inches tall, angled at the top to meet the roof

Bottom: 6 inches wide x 6 inches deep

Roof (2 pieces): 6 inches wide x 8 inches deep

Be sure to measure accurately and cut straight lines for a better fit. Use the pencil and measuring tape to mark the cuts before sawing.

Step 3: Drill the Entrance Hole and Ventilation Holes Drill an entrance hole in the center of the front piece. The size of the hole will depend on the type of bird you want to attract. A 1 1/2 inch hole is good for bluebirds, while a smaller 1-inch hole is suitable for wrens. Also, drill a few small ventilation holes near the top of the side pieces and a few drainage holes in the bottom piece. This will help to keep the birdhouse dry and well-ventilated.

Step 4: Assemble the Birdhouse Now it's time to assemble the birdhouse. Start by attaching the sides to the bottom piece, using screws or nails. If using glue, apply a thin layer to the edges before fastening. Next, attach the front and back pieces to the sides and bottom. Make sure all the pieces are aligned properly before securing them. Finally, attach the roof pieces to the top. The back piece should overhang slightly.

Step 5: Sand and Finish Once the birdhouse is assembled, use sandpaper to smooth any rough edges or splinters. This will make the birdhouse safer for the birds and give it a more finished look. If desired, paint or stain the birdhouse with exterior-grade paint or stain. This will help to protect the wood from the elements and prolong the life of the birdhouse. Choose colors that are natural and blend in with the surroundings. Avoid bright or garish colors, as these may deter birds. Allow the paint or stain to dry completely before hanging the birdhouse.

Step 6: Mount the Birdhouse Choose a suitable location for your birdhouse. Ideally, it should be in a sheltered spot, away from direct sunlight and strong winds. Mount the birdhouse on a tree, post, or fence, using screws or nails. Make sure it is securely attached. Consider adding a predator guard (a metal or plastic shield around the entrance hole) to protect the birds from squirrels, cats, and other predators. Clean the birdhouse out once a year, after the nesting season is over.

Conclusion: Enjoy Your New Birdhouse Congratulations! You've built your own simple wooden birdhouse. Now, sit back and enjoy watching the birds move in and make it their home. This project is a great way to connect with nature and provide a safe and welcoming space for your feathered friends. Remember to clean it out annually to keep it habitable for years to come.

Best 20+ Flat Pictures & Images

unsplash.com

Flats Free Stock Photo

www.freeimages.com

What Is A Flat? Discover If This Rental Option Is Right For You

www.apartmentguide.com

Read More

164+ Shed With Roof Overhang Storage

164+ Shed With Roof Overhang Storage

  17.26    insanu

---

www.gazebocreations.com

Introduction: Building a Simple Storage Shed with Roof Overhang This post details the process of building a small, DIY storage shed with a roof overhang. This shed is perfect for storing garden tools, lawn equipment, or seasonal decorations. The roof overhang provides extra protection from the elements and adds a nice aesthetic touch. This project assumes basic carpentry skills and familiarity with power tools. Always prioritize safety and wear appropriate protective gear.

Materials List:

Pressure-treated lumber for the base frame (4x4 posts, 2x6 joists)

Framing lumber for the walls (2x4 studs, top and bottom plates)

Exterior plywood or siding for the walls

Roofing material (shingles, metal roofing, etc.)

Roofing felt or underlayment

Lumber for roof rafters and sheathing (2x4 rafters, plywood or OSB sheathing)

Fasteners (nails, screws, construction adhesive)

Door and hardware (hinges, latch, handle)

Window (optional)

Trim boards for finishing

Paint or stain for protection

Concrete blocks or gravel for leveling the base

Tools Needed:

Measuring tape

Pencil

Circular saw or miter saw

Drill/driver

Hammer

Level

Square

Safety glasses

Hearing protection

Gloves

Ladder

Utility knife

Staple gun (for roofing felt)

Step 1: Building the Base Frame Begin by laying out the dimensions of your shed on the ground. Dig out any vegetation and level the area. Place concrete blocks or a gravel bed to provide a stable and well-drained foundation. Cut the pressure-treated lumber to the desired lengths. Construct a rectangular frame using the 4x4 posts as corner supports and the 2x6 joists to create the frame's perimeter and interior supports, spacing them approximately 16 inches apart. Secure the frame with screws and construction adhesive. Ensure the frame is square and level before proceeding.

Step 2: Framing the Walls Cut the 2x4 studs to the desired height of your shed walls. Typically, 8-foot studs are used for an 8-foot wall height. Build each wall frame by attaching the studs to the top and bottom plates, spacing them 16 inches on center. Ensure the corners are square. Frame out openings for the door and any windows, providing additional support around these openings. Raise each wall frame and secure it to the base frame using screws or nails. Brace the walls temporarily to keep them plumb while you attach the remaining walls.

Step 3: Installing the Wall Sheathing Attach the exterior plywood or siding to the wall frames using nails or screws. Ensure the sheathing is flush with the edges of the frame. Cut out the openings for the door and windows. If using siding, overlap the pieces according to the manufacturer's instructions. This step provides structural integrity to the walls and protects the framing from the elements.

Step 4: Constructing the Roof Calculate the necessary roof pitch and rafter lengths. Cut the 2x4 rafters to the correct length and angle. Assemble the rafters, ridge board, and any necessary collar ties. Raise the roof frame and secure it to the top plates of the walls. Overhang the rafters beyond the walls to create the roof overhang. Attach the roof sheathing (plywood or OSB) to the rafters, ensuring it is securely fastened.

Step 5: Roofing Installation Cover the roof sheathing with roofing felt or underlayment, overlapping the edges according to the manufacturer's instructions. This provides a waterproof barrier. Install your chosen roofing material (shingles, metal roofing, etc.) according to the manufacturer's instructions. Ensure proper overlap and sealing to prevent leaks. Pay close attention to the edges and ridges of the roof.

Step 6: Installing the Door and Window (Optional) Install the door in the framed opening, ensuring it swings freely and latches securely. Attach the hinges, latch, and handle. If installing a window, follow the manufacturer's instructions for proper installation and sealing. Ensure the window is level and square in the opening.

Step 7: Adding Trim and Finishing Install trim boards around the corners, door, and windows to create a finished look and protect the edges of the siding. Caulk any gaps to prevent water infiltration. Paint or stain the shed to protect it from the elements and enhance its appearance. Choose a paint or stain that is suitable for exterior use.

Conclusion: Enjoy Your New Storage Shed Congratulations! You have successfully built a simple storage shed with a roof overhang. This shed will provide valuable storage space and protect your belongings from the elements. Remember to regularly inspect and maintain your shed to ensure its longevity. You can customize the shed further by adding shelves, organizers, or other features to suit your specific needs.

Cedar Lap Siding Deluxe Estate Sheds

www.gazebocreations.com

Cedar Lap Siding Saltbox Sheds

www.gazebocreations.com

Cedar Shed Kits, Cedar Garden & Storage Sheds

cedarshed.com

Read More

164+ Flat Roof

164+ Flat Roof

  17.24    insanu

---

www.permaroof.co.uk

Opening: DIY Flat Roof Birdhouse Want to attract feathered friends to your backyard while adding a touch of modern design? This step-by-step guide will show you how to build a stylish and functional flat roof birdhouse. It's a great project for beginner woodworkers and a fun way to recycle scrap materials. Let's get started!

Materials You'll Need:

Wood (pine, cedar, or reclaimed wood are all good choices) approximately 1/2" to 3/4" thick

Wood glue

Nails or screws (1 1/4" or 1 1/2")

Sandpaper (various grits)

Exterior wood sealant or paint

Drill with various sized drill bits (including a spade bit or hole saw for the entrance)

Saw (hand saw, jigsaw, or circular saw)

Measuring tape or ruler

Pencil

Clamps

Step 1: Cutting the Wood Pieces Begin by determining the desired size of your birdhouse. A good starting point is a 6"x6" base. Using your saw, cut the following pieces:

Base: 6" x 6" (1 piece)

Front: 6" wide x 8" tall (1 piece)

Back: 6" wide x 8" tall (1 piece)

Sides: 6" deep x 8" tall (2 pieces) note that the top edges need to be angled for the flat roof

Roof: 7" x 8" (1 piece) to provide a slight overhang

The side pieces will need an angle cut. The best method for angled side walls on a bird house is to make the front wall tallest, the back wall a bit shorter and the side walls the median length. So, measure 8" on one side and 7.5" on the other side and connect the dots to make a smooth angled cut. Remember to make sure the two sides are mirror images of each other.

Step 2: Drilling the Entrance Hole Decide where you want the entrance hole to be located on the front piece. A good height is about 2" to 3" from the top edge. Choose a drill bit size appropriate for the type of birds you want to attract (1 1/2" is suitable for wrens and chickadees). Use a spade bit or hole saw to drill a clean hole.

Step 3: Assembling the Birdhouse Walls Apply wood glue to the edges of the base piece where the front, back, and side pieces will attach. Clamp the front, back, and side pieces to the base, ensuring they are flush and square. Secure the pieces with nails or screws, driving them in at an angle for added strength. Let the glue dry completely.

Step 4: Attaching the Side Walls Now glue and screw or nail the side walls onto the front and back walls. Make sure that the side walls are flush with the front and back walls and firmly in place so that they are ready to take the roof.

Step 5: Attaching the Roof Apply wood glue to the top edges of the front, back, and side pieces. Position the roof piece on top, ensuring it overhangs slightly on all sides. Clamp the roof in place and secure it with nails or screws. Let the glue dry completely.

Step 6: Sanding and Finishing Once the glue is dry, sand all surfaces of the birdhouse to remove any rough edges or splinters. Start with a coarser grit sandpaper (80-120) and finish with a finer grit (220). Apply an exterior wood sealant or paint to protect the birdhouse from the elements. Be sure to choose a non-toxic finish that is safe for birds.

Step 7: Adding Drainage and Ventilation Drill a few small drainage holes (1/4") in the bottom of the birdhouse to prevent water from accumulating. Drill a few small ventilation holes near the top of the sides to help regulate temperature inside.

Step 8: Mounting the Birdhouse Decide where you want to mount your birdhouse. You can attach it to a tree, post, or fence. Use screws or nails to securely attach the birdhouse to the chosen location.

Conclusion: Enjoy Your New Birdhouse! Congratulations! You have successfully built your own flat roof birdhouse. Now, sit back and enjoy watching the birds move in and make it their home. Remember to clean out the birdhouse annually to keep it a healthy and safe environment for your feathered residents.

Flat Roof Gallery

www.permaroof.co.uk

Contemporary Flat Roof Houses

lomicu.weebly.com

Flat Roof Construction

www.topseal.co.uk

Read More